DSC PC 5010 Specifications download pdf (Page 6)

G E T T I N G S T A R T E D

2.2 Terminal Descriptions

AC Terminals - AC

The panel requires a 16.5 volt, 40 VA transformer. Connect the transformer to an unswitched AC source

and connect the transformer to these terminals.

Do not connect the transformer until all other wiring is complete

Battery Connection

The battery is used to provide back up power in the event of an AC power failure and to provide

additional current when the panel demands exceed the power output of the transformer, such as when

the panel is in alarm.

Do not connect the battery until all other wiring is complete

Connect the RED battery lead to the positive of the battery, the BLACK battery lead to the negative.

Auxiliary Power Terminals - AUX+ and GND

These terminals provide up to 500 mA of additional current at 12 VDC

(rated 11.6-12.6 V

for UL

residential applications)

for devices requiring power. Connect the positive side of any device requiring

power to the AUX+ terminal, the negative side to GND. The AUX output is protected; if too much current is

drawn from these terminals (wiring short) the panel will temporarily shut off the output, until the problem is

corrected.

Bell Output Terminals - BELL+ and BELL-

These terminals provide up to 3 Amps of current at 12 V

(rated 11.6-12.6 V

for UL residential

applications)

(with stand-by battery; 700 mA continuous) for powering bells, sirens, strobes or other

warning type equipment. Connect the positive side of any alarm warning device to BELL+, the negative

side to BELL–. The BELL output is protected; if too much current is drawn from these terminals (wiring

short) the BELL fuse will open.

The Bell output is supervised. If no alarm warning device is being used connect a 1000 ohm resistor

across BELL+ and BELL– to prevent the panel from displaying a trouble condition

(See Section 3.4 “[

✱

]

Commands, [

✱

][2]”).

Keybus Terminals - RED, BLK, YEL, GRN

The Keybus is used by the panel to communicate with modules and by modules to communicate with the

panel. Each module has four Keybus terminals that must be connected to the four Keybus terminals on

the panel. For more information,

see Section 2.3 “Keybus Operation and Wiring”.

Programmable Outputs - PGM1 and PGM2

Each PGM output is an open collector switch to ground. That is, when the PGM

output is activated by the panel the terminal will switch to ground.

PGM1 can sink up to 50 mA of current to activate LEDs or a small buzzer.

Connect the positive side of the LED or buzzer to AUX+, the negative side to

PGM1. If more than 50 mA of current is required a relay must be used. Refer to

the following diagram:

PGM2 is high current PGM (300mA) which operates similar to PGM1. It can

be used for two wire smoke detectors (

See Section 2.9 “Zone Wiring - Fire

Zone Wiring”)

with the jumper CON1 removed. Otherwise, the CON1 must

remain on at all times.

Zone Input Terminals - Z1 to Z8

Each detection device must be connected to a zone on the control panel. It is suggested that each zone

have one detection device however it is possible to wire multiple detection devices to the same zone.

For zone wiring specifics,

see Section 2.9 “Zone Wiring” .

Telephone Connection Terminals - TIP, RING, T-1, R-1

If a telephone line is required for central station communication or downloading, connect an RJ-31X jack

in the following manner:

• RING - Red Wire _______ Incoming line from

• TIP - Green Wire telephone company

• R-1 - Grey Wire ________ Outgoing line to

• T-1 - Brown Wire house telephone(s)

1 2 3 4 5 6 7 8 9 10 11 ... 47 48

Comments to this Manuals

No comments

DSC PC 5010 Specifications Page 6

Comments to this Manuals

Related products and manuals for Security access control systems DSC PC 5010