DSC PC15OO Installation Manual download pdf (Page 15)

PROGRAMMING SECTIONS

[00] Binary Programming

This section is normally used upon instruction from factory

technical personnel for specialized programming not covered

by the standard programming instructions.

[01] 1st Phone Number

This is the first telephone number the Communicator will dial.

See Section [25], Communicator Call Direction.

After entering Section [01] for programming, enter the

telephone number the same way you would dial it on a touch-

tone phone. Press [#] after the last digit to complete the

telephone number programming.

A second dial tone search, as required in a PBX system, can

be added by programming a HEX ‘D’ between the digits in the

phone number where it is required. To enter a HEX ‘D’, press

[

∗

] then [4] then [

∗

Instead of a dial tone search, a pause of 4 seconds can be

inserted between digits in a telephone number.

Enter [

∗

, 2,

∗

] to dial a ‘

∗

’ (HEX ‘B’)

Enter [

∗

, 3,

∗

] for a 4-second pause (HEX ‘C’)

The total number of digits, including dial tone searches and

pauses, must not exceed 16. Remember, press [#] to

complete entry of the telephone number.

When complete, enter two digits to program another section.

[02] 1st Account Code

The 1st Account Code is always transmitted to the 1st

telephone number to identify the customer. Enter a 4-digit

number. If the HEX digits ‘A’ to ‘F’ are required, remember

to enter [

∗

] before and after the digit entry.

Where a zero is required in the account code, enter HEX ‘A’

(

∗

, 1,

∗

) to transmit 10 pulses which will be interpreted as a

zero by the monitoring station receiver.

If a 3-digit code is required, as in 3/1 formats, enter [0] as the LAST

digit. The [0] represents a null digit where no pulses are transmitted.

[03] 2nd Phone Number

This is the second telephone number to which the

communicator will dial. See [01] for programming instructions.

[04] 2nd Account Code

The second account code is always transmitted to the 2nd

telephone number. See [02] for programming instructions.

Reporting Codes [05] to [10]

These sections are used to program the communicator

reporting codes. A reporting code is transmitted along with

the account code with each transmission. If the reporting

codes are not programmed, no transmission will be sent

when an event takes place (i.e. alarm, restoral, opening /

closing, trouble, etc.). To prevent a transmission from being

sent for any event in the following sections, leave it

unprogrammed or enter [00] as the reporting code.

Section [05] and [06] each have 6 reporting codes. Sections

[07], [08] and [10] each have 7 reporting codes, while

Section [09] has 8 reporting codes. Once a section is

entered, the system expects a series of 2-digit numbers to be

entered. The keypad beeps twice and the “Armed” light

flashes after each 2-digit entry. After the last 2-digit number is

entered, programming of the current section is complete. The

keypad gives a series of beeps, the “Ready” light goes OFF

and the “Armed” light comes ON. The keypad is then ready to

accept the next 2-digit section number for programming.

When changing reporting codes in a section, you can scroll

to the code you wish to change by pressing the [F] key. Only

codes actually changed will be altered in the EEPROM.

Press [#] to exit from the programming sequence.

[05] Zone Alarm Reporting Codes

Once Section [05] is entered, the panel expects 6 2-digit

numbers for the Alarm Reporting Codes for zones 1 to 6.

These codes are used by the communicator when there has

been an alarm on zones 1 to 6.

Listed below are several programming examples and the

resulting transmission using different formats for the reporting

codes. Obtaining different formats requires entering data in the

Account Code Section [02] or [04], the Reporting Code Sections

[05] to [10], and the Communicator Format Section [23].

3/1 FORMAT - Non-extended reporting

Requires:

• 3-digit account code in sections [02] or [04].

i.e. Enter 1230 for account code 123

• Format Code [0], [1], [2], [3], [4] depending on

receiver type in Section [23].

• Single line digit Alarm Reporting Code Section [05]

i.e. Enter [30] for single digit code 3 (0 = no pulses)

TRANSMISSION SENT: 123 3

4/2 FORMAT - Non-extended reporting

Requires:

• 4-digit account code in sections [02] or [04].

i.e. Enter 1234 for account code 1234

• Format Code [0], [1], [2], [3], [4] depending on

receiver type in Section [23].

• 2-digit Alarm Reporting Code in Section [05]

i.e. Enter [31] for 2-digit code 31

TRANSMISSION SENT: 1234 31

3/1 FORMAT - Extended reporting

Requires:

• 3-digit Account Code in Section [02] or [04]

i.e. Enter 1230 for code 123

• Format Code [8], [9], [A], [B], [C] depending on

receiver type in Section [23]

• 2-digit Alarm Reporting Code in Section [05]

i.e. Enter [31] for 2-digit code 31

TRANSMISSION SENT:

1st ROUND 123 3

2nd ROUND 333 1

If a transmission is not wanted for a particular reporting code,

then enter ‘00’ or ‘FF’ to disable that reporting code.

[06] Zone Restoral Reporting Codes

These reporting codes are used by the communicator to

transmit zone restorals for zones 1 through 6. Use instructions

in Section [05] above as a guide for programming.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 35 36

Comments to this Manuals

No comments

DSC PC15OO Installation Manual Page 15

Comments to this Manuals

Related products and manuals for Security access control systems DSC PC15OO