DSC PC15OO Installation Manual download pdf (Page 13)

PROGRAMMING GUIDE

Introduction

The PC1500 is fully programmable from the keypad and uses

an EEPROM memory which can be reprogrammed thousands

of times. The EEPROM memory will not lose the program data

even on total loss of power. The essential information which

defines the operation of the control panel is stored in a

section of the EEPROM memory which is accessible using

the Installer’s Programming code or via downloading. If the

Installer’s code is forgotten, the EEPROM may be reset to the

factory default code. See Section [30], Reset to Factory

Default.

Programming

With the panel in the disarmed mode, enter [

∗

][8][1500].

The panel can only be programmed while it is in the disarmed

mode. The default installer’s code is 1500; the installer’s

code can be changed. See Section [20], New Installer’s

Code.

Once the installer’s command is entered, the “Armed” light

will come ON steadily and the “Memory“, “Bypass” and

“Trouble” lights will flash. This indicates that the panel is

ready for programming. NOTE: If no key entry is made for

2 minutes, the panel will return to the Ready mode and the

complete installer’s command will have to be entered before

programming can be resumed.

With the “Armed” light ON steadily, enter 2 digits for the

section you wish to program. The sections for the PC1500

panel range from [01] to [36], and each section can be

programmed independently. Section [00] is reserved for

binary programming which is normally done on instruction

from factory technical personnel.

Once the 2 digits for the section you wish to program are

entered, the “Armed” light will go OFF, the “Ready” light will

go ON steadily, and the keypad sounder will beep 3 times.

The keypad is now ready to accept data for the selected

section.

Most sections contain groups of 2-digit entries and the

keypad buzzer will beep twice after each 2-digit group is

entered.

When the section is first entered, the first 4 zone lights will

indicate, in a binary format, the value of the first digit in that

section (refer to “Binary Data Display” on the next page). If

you wish to change that digit, simply enter the new digit from

the keypad. If you wish to keep that digit unchanged, you can

enter the same number or skip the digit by pressing the [F]

key. Once the first digit has been entered or skipped, the 4

zone lights will display the value of the second digit. After

each digit is entered or skipped, the zone lights show the

value of the next digit in the binary format.

When the required data for the section being programmed is

completely entered, the keypad sounder will beep several

times and the “Armed” light will come ON to indicate that the

expected data has been entered.

At this point, you will still be in the program mode and need

only enter the section number for the next section you wish

to program.

It is not necessary to program all 2-digit pairs in any given

section. A section can be entered and selectively programmed

by going only to the digit(s) you wish to change and then

pressing [#] to return to the programming mode where you

can then enter another section number for programming. For

2-digit pairs, both digits must be programmed before pressing

the [#] key. Only the data entered before pressing the [#] key

will be changed in the EEPROM.

Program Data Review

• Enter the section you wish to program by entering the 2-

digit section number.

• The first 4 zone LEDs will represent the value, in binary

format, of the first digit in that section.

• Each press of the [F] key will advance the display to the

next digit.

• At the end of the section, the keypad will beep several

times and then return to the program mode so that

another section can be selected for review or

programming.

NOTE: Only Sections [01] through [11], [15], and [17]

through [28] can be reviewed using the method described

above.

Sections [12], [13], [14], [16], [31], [32], [34]

These sections use the zone lights to indicate which functions

are active and which number key to press to turn them ON

and OFF. When one of these sections is entered, zone lights

1 to 6 will display which functions are currently ON. Pressing

the key number corresponding to the zone light number will

alternately turn the function ON and OFF, and the zone light

will correspond to this. All functions can be turned OFF at

once by pressing [0]. When the correct selections have been

made, press [#] to save the selections in memory and return

to the program mode where another section can be selected.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 35 36

Comments to this Manuals

No comments

DSC PC15OO Installation Manual Page 13

Comments to this Manuals

Related products and manuals for Security access control systems DSC PC15OO