DSC PC 5010 Installation Manual download pdf (Page 27)

Programming Sections:

5.3 Basic Programming PWS Sect 3

[005] - System Times

This section has 3 sub-sections, 1 for each of the 2 parti-

tions, and 1 for the Bell time-out. A 2-digit entry is

required to access these sub-sections.

NOTE:

Entry of 000 in these sections will result in a 255- sec-

ond time.

Sub-Sections 1-2 each require three 3-digit entries.

[01] - [

[01] - [[01] - [

[01] - [02

0202

02]

]]

] Entry Delay 1, Entry Delay 2, and Exit Delay

per partition.

•Entry Delay 1:

Entry Delay 1:Entry Delay 1:

Entry Delay 1: 030-240 Seconds

This value determines the Entry delay time for Delay 1

type zones. The default Entry Delay 1 time is 30 seconds.

•Entry Delay 2:

Entry Delay 2:Entry Delay 2:

Entry Delay 2: 030-240 Seconds

This value determines the Entry delay time for Delay 2

type zones. The default Entry Delay 2 time is 30 seconds.

•Exit Delay:

Exit Delay:Exit Delay:

Exit Delay: 045-255 Seconds

This value determines the Exit delay time when arming

the system. The default Exit Delay time is 60 seconds.

NOTE:

The Exit Delay must not exceed 255 seconds. The

minimum possible entry is 45 seconds.

NOTE:

If the Exit Delay is silent (Section 014, Option 6 or

Stay Function Key Arming) the Exit Delay will be twice the

programmed value (060-510 seconds).

[09] Bell Time-out:

[09] Bell Time-out:[09] Bell Time-out:

[09] Bell Time-out: 001-255 Minutes

The Bell Time-out for all 2 partitions will be the same.

The siren will silence after the number of minutes pro-

grammed for the Bell Time-out

Bell Time-out Bell Time-out

Bell Time-out value has passed. The

default Bell Time-out is 4 minutes

The panel supervises the Bell output. If an open condition

is detected, the panel will immediately indicate a Trouble

condition by beeping the keypad twice every 10 seconds

to alert the owner to the problem. The panel can send a

Bell Circuit Trouble

Bell Circuit Trouble Bell Circuit Trouble

Bell Circuit Trouble and Trouble Restoral

Trouble Restoral Trouble Restoral

Trouble Restoral reporting codes

to indicate the situation (see section 5.6, ‘Communicator

Programming’ PWS Sect 6).

If the Temporal Three Fire Signal

Temporal Three Fire Signal Temporal Three Fire Signal

Temporal Three Fire Signal option is enabled, all

Fire signals will follow the Temporal Three Pattern as

described in NFPA 72. If turned OFF all Fire signals will

sound a one second on, one second off cadence.

If Fire Bell Continuous

Fire Bell Continuous Fire Bell Continuous

Fire Bell Continuous is enabled, the alarm output will

sound until a code is entered. If disabled, the alarm will

sound until a code is entered or the bell time-out has

expired.

NOTE:

Only fire zones will follow the Temporal Three Fire

Signal.

Bell Time-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [005]

Bell Circuit Trouble Reporting Code . . . . . . . . . . . . . . Section [345]

Bell Circuit Trouble Restoral Reporting Code. . . . . . . . Section [346]

Temporal Three Fire Signal

Enable/Disable . . . . . . . . . . . . . . . . . . . . . Section [013], Option [8]

Fire Bell Continuous . . . . . . . . . . . . . . . . . Section [014], Option [8]

25 Interior Delay Zone

The Interior Delay Zone is normally used with motion detectors and has a standard Exit Delay time. If the panel is

armed, and a Delay zone is violated during the Exit Delay (or the Away function key is used), the Interior Delay Zone

will be active at the end of the Exit Delay. This zone will cause an instant alarm when violated. This zone type will fol-

low the Entry Delay time provided that a Delay zone is violated first. If the panel is armed, and a Delay zone is NOT

violated during the Exit Delay (or the Stay function key is used, or [*][9] armed), a violation of this zone type will ini-

tiate Entry Delay 1.

26 24-hr Non-Alarm

These zones are active at all times but do not cause an alarm, and do not show up in alarm memory. Zone Attributes

such as Zone Bypassing and Door Chime affect the functionality of this zone. A 24-hr Non-alarm zone may be used

for Zone Follower automation applications.

NOTE: This zone type will be active in Walk Test. Tampers and Faults. Zones programmed as 24-hr Non-

alarm type will not cause alarms.

NOTE: Alarms on this zone will not initiate Downlook.

27 Delayed 24-hr Water-

flow

These zones will follow the waterflow Delay Timer. When a delayed waterflow zone is violated, the waterflow timer

will start, (any subsequent delayed waterflow zones that become active do not reset or abort this timer). If there are

still delayed waterflow zones open when the waterflow timer expires, the panel will go into alarm and communicate

the event(s) regardless of the armed state.

28 Instant 24-hr Water-

flow

A waterflow alarm is a Fire alarm. The Fire related bells and Aux functions are activated. This Zone type functions

similar to Type 27 (Delayed 24-hr waterflow), but does not follow the Waterflow Delay Timer. When this zone is vio-

lated, it will immediately go into alarm. This zone type always uses a single EOL configuration.

29 Auto Verified Fire Zone

This zone ensures that an alarm condition persists by resetting a tripped sensor in a fire zone and confirming that the

sensor has remained tripped or is waiting for the sensor to re-trip within a set period of time (e.g., cycling power to

a smoke detector to ensure the condition persists when power is restored). The alarm sequence for the zone is indi-

cated below:

Step #1 Duration 20 Seconds Sensor Reset

Step #2 Duration 10 Seconds Settle Time (Power-up)

Step #3 Duration 60 Seconds Check for Verified Alarm

NOTE: If another Fire device detects Fire during the Auto Verify or Delay sequence, the sequence is termi-

nated and alarms are immediately generated for all pending zones. This applies to all other Fire zones on

the system regardless of the partition assignments (i.e., two fire alarms anywhere on the system will can-

cel all pending fire delays and create immediate alarms).

30 Fire Supervisory Zone

When this zone is violated, the system turns on the keypad buzzer, and communicates the supervisory alarm condi-

tion to the monitoring station. The buzzer will not follow the Bell Time-out. To silence the buzzer, a valid access code

must be entered.

NOTE: The fire supervisory alarm is not affected by the waterflow silence inhibit option described in

[018], Option 4, Pg 32

31 Day Zone

A zone programmed as this type has different characteristics in the armed and disarmed state. In the disarmed state,

violating this zone will sound the keypad buzzer but will not log or report the event. In the armed state, violating this

zone will sound the bell and communicate the event.

87 Delayed 24-hr Fire

(Wireless)

Used only with wireless smoke detectors. Functions same as Zone Type [07].

88 Standard 24-hr Fire

(Wireless)

Used only with wireless smoke detectors. Functions same as Zone Type [08].

[001]-[002] ZONE DEFINITIONS

Option Zone Type Description

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 59 60

Comments to this Manuals

No comments

DSC PC 5010 Installation Manual Page 27

Comments to this Manuals

Related products and manuals for Security access control systems DSC PC 5010