DSC PC4020 - V3.3 Installation Manual Page 1

PC4020 v3.3 (US, UL) • Installation ManualDLS-3 v1.3WARNING: This manual contains information on limitationsregarding product use and function and inf

6Addressable DevicesThe following addressable devices are available:• AMS-220/220T smoke detector with optional tempera-ture sensor*• AMB-300 PIR dete

Installation and Wiring7SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Typically, this output is used for providing power to latch-ing

8The control panel monitors the presence of AC. Upon theloss of AC power a trouble condition will be generated.The keypad trouble light will turn on.

9Section 3: How to Program 3.1 Introduction to ProgrammingThe PC4020 is programmed via a menu system. Use thearrow keys (<>) to scroll through d

103.4 Programming Hexadecimal DataHexadecimal or ’Hex’ digits are often required for a pro-gramming item, such as telephone numbers and reportingcodes

11Section 4: Module Enrollment4.1 Enrolling Keypads and ModulesOnce the wiring of all keypads and modules is complete,they must be enrolled on the sys

124.3 Confirming ModulesRef # [0202] then scroll to desired moduleIn case module numbers were not recorded, you can ver-ify this information through t

13Section 5: Partitions and Zones5.1 Zone SupervisionRef # [000204] ’Zone Supervision’The control panel must be instructed to supervise eitherNo End o

14NOTE: When a partition is deleted, the zones assignedto it are removed from the Zone Assignment.Copying PartitionsRef #: [0102]Enter this section to

Partitions and Zones15SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 [5] Save will save any changes and exit zone label pro-gramming.

WARNING Please Read CarefullyNote to InstallersNote to InstallersNote to InstallersNote to InstallersThis warning contains vital information. As the o

16the burglary outputs; if disarmed it will activate thekeypad buzzer. When the partition is disarmed, thiszone will not activate the verbal alarm fea

Partitions and Zones17SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Push To Set Zone Type (32)*When a partition to which this zone is

18Section 6: Keypad Operation6.1 Partition KeypadsA partition keypad is a keypad that can access one parti-tion. You can assign a keypad to a partitio

19On each keypad, you can program each function key sothat users will need to enter an access code before thepanel performs the function. To do this,

20lowed by the number of incorrect codes. Valid entries arefrom 000-255. The default setting is 005.The Lockout Duration is the length of time during

Keypad Operation21SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 User Functions (10)This function key provides the user with a simple

22Section 7: Installer and Access CodesNOTE: Security codes should be changed from theirdefault settings to ensure the security of the system. Donot

23Program A New CodeTo program the new access code, perform the following:1. From the Program Code menu, use the arrow keys toscroll to the first mess

24[1] Dial tone search: This character will force the panelto search for a dial tone at that point in the telephonenumber. A ’D’ on the display repres

Installer and Access Codes25SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 7.6 Delete An Existing CodeAn access code may be erased i

iTable of ContentsSection 1: Introduction 11.1 Out of the Box ... 11.2 Speci

267.8 Guard CodeRef #: [000004]The Guard code can only be changed in this section andcannot be altered by the user. The Guard code can always be used

27Section 8: Arming and Disarming8.1 Arming and Disarming OptionsRef #: [0100XX01] where XX = Partition 01-08The following arming and disarming option

28Section 9: Entry and Exit DelayUpon arming, the panel will begin the Exit Delay. If the ’Exit Delay Aud’ option is enabled, the keypad will beep eve

29Section 10: System Programming10.1 AC/DC Power OptionsRef # [000200]The following options are used to determine the powersettings for the system. Pr

30Clock AdjustRef #: [00020308]This option is to compensate for any timebase inaccuracy.The panel will replace the last minute of each day with thenum

System Programming31SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 10.7 Telephone Line SupervisionRef #: [000401]Scroll to the TLM En

32Waterflow DelayRef #: [00020311]This delay is to prevent false alarms due to surges in thesprinkler system. The Maximum delay allowed is 90 sec-onds

33Section 11: Programmable Outputs11.1 Main Panel OutputsThe main panel has four programmable outputs: Bell,SAUX+, PGM1 and PGM2. Adding PC4216/PC4204

34closed. In order for the output to activate, the door chimefeature must be enabled.TLM Only (13)The output will activate when a telephone line troub

Programmable Outputs35SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 allow the output to be toggled on and off using the corre-spondi

iiPC4020 Wiring Diagram

36Kissoff Pulse (00)Any output programmed for ’Kissoff’ can be active from000 to 255 seconds. The default setting is 003 seconds.Ground Start (01)Any

37Section 12: Communications ProgrammingAll options concerning communications can be programmed in the following sections, including telephone numbers

38disabled, the panel will send the restoral immediatelywhen the zone is restored (default=No).NOTE: DO NOT enable this feature if the previous’Resto

Communications Programming39SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 dialer direction settings. If disabled, the panel will fol

40Contact ID Identifier Toggle Options• Partial Closing Identifier: This toggle option controlswhether the Partial Closing reporting code will betrans

41Section 13: DownloadingNOTE: DLS-3 v1.3 or higher is required. Downloading is not to be enabled on UL Listed systems.13.1 Downloading OptionsAutomat

42Section 14: Event Scheduling Event scheduling allows for a variety of timed events to occur on specific dates and at specific times. Openings and cl

43Open/Close Suppression ToggleIf the Open/Close Suppression schedule is being used tosuppress openings, toggle this option to [Y]. If it is to sup-pr

44Section 15: LINKS Communications15.1 LINKS1000 (Cellular Communications)When using a LINKS1000 Cellular Communicator as aprimary or backup means of

45Section 16: Diagnostics and Troubleshooting16.1 General DiagnosticsRef #: [04]The diagnostics function is designed to help you trackdown any problem

1Section 1: Introduction1.1 Out Of The BoxPlease verify that the following components are includedin the PC4020 package.❑ 1 PC4050C or PC4001C cabinet

46occurs, the panel will not restore the trouble until it hasbeen viewed using the [*][2] trouble display. The troublewill not be restored until it ha

47Alt. Comms AC TroubleThe alternate communicator has lost AC power.Alt. Comms Bat-tery TBLThe battery connected to an alternate communicator module i

48Appendix A: Reporting CodesNotes on Contact IDThe following is a list of Contact ID reporting codes. Thefirst digit (in parentheses) will automatica

49* A/R = alarms/restorals; O/C = openings/closings; O = other** PPP = partition number; UUU = user number (user 1000 to 1500 = 999); ZZZ = zone numbe

50* A/R = alarms/restorals; O/C = openings/closings; O = other** PPP = partition number; UUU = user number (user 1000 to 1500 = 999); ZZZ = zone numbe

51Appendix B: Zone Reporting CodesFor notes on Contact ID and SIA reporting codes, see Appendix A.* If Contact ID is used, the above reporting codes a

52Appendix C: ASCII Characters

53IndexAAccess Codegrand master 22guard 26options 26second master 22walk test 22Access Levels 26Account Number 13, 37Addressable Loopcurrent

UL Listed Commercial and Residential InstallationsThe installation requirements listed below must be met for the following grades of service.Note: All

FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use th

2Section 2: Installation and Wiring2.1 Planning the SystemThe speed and efficiency of installing a MAXSYS systemwill be greatly enhanced by planning t

Changes for PC4020 v3.3The PC4020 v3.3 software incorporates several new features and changes. The most impor-tant additions are listed below:New Opti

Installation and Wiring3SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PGM1 (50/170mA max.*)PGM2 (50/170mA max.*)Combus (500mA max.)**

4Capacitance LimitsAn increase in capacitance on the Combus will affect datatransmission and will cause the system to slow down.Capacitance will incre

Installation and Wiring5SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Resistors should always be placed at the device end ofthe wire