DSC PC1500 - REV8 Instruction Manual download pdf (Page 6)

Enter Code to

Arm System

Secure System

Before Arming < >

Enter Code to

Arm System

Exit Delay in

Progress

✱ WARNING ✱

Bypass Active

✱ WARNING ✱

System Trouble

Programming Security Codes

Master Code

The installer can program the system so that the Master Security Code can be

changed by the user. If your system is set up to allow a changeable Master Code,

follow the instructions below.

Start in the “Disarmed” mode and press the [✱] key to enter the “functions” list.

Scroll < > to.. Press [5].

Display will read.. Enter your current Master Code.

Display will read.. Enter “1” for PC2550, PC2500, PC1550

and PC1500 systems.

or.. Enter “01” for PC3000 system.

Display will read..

Enter the new Master Code. The Master Code must be 4 digits. Enter digits 0

through 9 only. Once the new code is entered the keypad sounder will beep 3

times and the display will read..

Press [#] to exit.

Remember to record your new Master Code on the System Information page in this

booklet.

Additional Codes

• PC1500 and PC1550 Control Panels

Up to 5 additional user codes (2 through 6) may be programmed. The 6th user

code can be made a One Time use code by your installer.

• PC2500 Control Panel

Up to 7 additional user codes (2 through 8) may be programmed. The 8th user

code can be made a One Time use code by your installer.

• PC 2550 and 3000 Control Panels

Up to 15 additional user codes (2 through 16) may be programmed. The 16th

user code can be made a One Time use code by your installer.

To erase, add or change a user code, press [✱] to enter the “functions” list.

Scroll < > to.. Press [5].

Display will read.. Enter Master Code.

Display will read or

Press (5) for...

Access Codes

Enter Master

Access Code...

Select Code< >

Code 1 P

Select Code< >

Code 01 P

Enter 4 Digit

Access Code...

Press (5)

Access Code...

Enter Master

Access Code...

Select code < >

Code (xx)

Select Code < >

Code (x)

Select Code < >

Code 01 P

Master Code

The four digit Master Code is used for arming and disarming the security system,

programming additional security codes and changing other features. The Master

Code will be supplied to you by your installer. If enabled by your installer, the

Master Code can be changed at any time. (See Programming Security Codes

section.)

Arming

If this display is showing, check to see that all zones are secure

by closing all doors/windows and stopping motion in areas

covered by motion detectors. If a zone will not clear, it may be bypassed to allow

partial arming. Note: A bypassed zone reduces your protection. If a zone

cannot be cleared, call your installer for service.

If this display is showing, check to see that the system is clear

of troubles and that there are no zones bypassed. The system

may be armed with zones bypassed and/or trouble conditions present but to do so

will compromise protection. Check to see which zones are bypassed and that

these zones are intentionally bypassed. If a trouble is present, see the section

“Viewing Trouble Conditions”.

If this display is showing, there are no troubles or bypassed

zones and the system may be fully armed. To arm the system,

enter your four digit security code. The keypad sounder will beep as each digit is

entered. If the security code was incorrectly entered, the keypad sounder will beep

steadily for two seconds and the display will not change.

Once the correct security code has been entered, the display

will be as shown on the left. Exit the premises through the door

indicated by your installer as the “exit-entry” door. Once the “exit” delay expires,

the system will be armed and will display the following message

Enter Code to

Disarm System

If you enter your security code with one or more zones bypassed, the following

message will appear as soon as you enter the first digit.

If this message appears, ensure that the zones bypassed are

intentionally bypassed.

If you enter your security code and a system trouble is present, the following

message will appear as soon as you enter the first digit.

If this message appears, check to see what the trouble

condition is and call for service. See the section “Viewing Trouble

Conditions”.

If you arm the system with a zone bypassed or with a trouble present your

security protection is reduced.

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

DSC PC1500 - REV8 Instruction Manual Page 6

Comments to this Manuals

Related products and manuals for Fire protection DSC PC1500 - REV8