DSC PC1500 - REV8 Instruction Manual download pdf (Page 9)

Secure System

Before Arming< >

System Open:

“Message” < >

Press either scroll key to find the zone to be bypassed.

Enter the zone number as indicated on the display.

“BP” will appear on the display to show that the zone is

bypassed. To remove a zone bypass, press the zone number

as indicated at this point and “BP” will disappear from the

display to show that the zone is no longer bypassed.

If that zone was open when you went [✱] [1], it will be seen on the display as

follows..

or or

If the same zone is already bypassed or you bypass the zone, it will then say BP

instead of OP.

To leave the bypass mode, press the [#] key.

Zone bypasses are automatically removed each time the system is disarmed and

must be re-applied before the next arming.

Note: For security reasons your installer may program the system to prevent

the bypass command from operating on certain zones.

Viewing Trouble Conditions

The control panel continuously monitors a number of possible trouble conditions. If

one of these conditions occur, the keypad sounder will beep twice every 10

seconds.

If the panel is armed when the trouble occurs, the keypad will beep but the

display will not change unless it is a fire zone trouble in which case it will toggle

the message. Enter your security code to disarm the panel. The keypad sounder

will stop beeping and the display will read..

If the panel is disarmed when the trouble occurs, the display will be as shown

above and the keypad sounder will beep twice every 10 seconds. Pressing any

key will silence the keypad sounder. To view the trouble, press either scroll key.

This message will be displayed.

Press the [✱] then [2] keys to view the trouble.

This message will be displayed.

Press the scroll key to see more troubles.

If there are no more troubles, this message will be displayed.

Press the [#] key to exit trouble viewing.

Select Zone

“Zone Name” < >

(xx) to Bypass

“Zone Name”

(xx) to Clear

“Zone Name” BP

Select Zone < >

Zone x OP

(xx) to Bypass

Zone x OP

(#) to Exit...

Zone x OP

(#) to Exit...

“Zone Name”

✱ Trouble ✱

Fire Zone

Enter Code to

Arm system... < >

System Trouble

(✱, 2) to View < >

View Trouble < >

“Trouble Message”

View Trouble < >

(#) to Exit...

If there is only one trouble condition, the display will show the [#] to exit message.

If there are multiple troubles, the display will show each one as the scroll key is

pressed. Press the [#] key to exit the trouble view mode. The trouble indicator (<

>) will remain on the display until the trouble condition is cleared. Note: A

TROUBLE condition reduces the security your system is designed to provide.

Call your installing company for service.

The system is continuously monitored for the following trouble conditions.

• Low voltage or disconnected stand-by battery.

• Loss of AC power.

• Day circuit trouble (during the disarmed state) - Not applicable to PC1550/1500.

• Telephone line problem - Not applicable to PC1550/1500.

• Unsuccessful communication attempt with the monitoring station.

• Bell circuit fault (open circuit).

• Fire alarm circuit trouble (open circuit).

• Loss of time on the system clock.

Testing

It is recommended that the system be tested weekly.

1.Inform the monitoring station that you are testing.

2.Disarm the system. In the disarmed mode the display will read..

Enter Code to

Arm System...

3.Perform a Bell/Battery test by pressing [✱] [6] [Master Code] [8]. The Bell and

keypad buzzer will sound for 2 seconds. Press [#] to exit.

4.Activate each sensor in turn, e.g. open door or window, walk in a motion

detector area. As each zone is activated, this message will

be displayed.

Press either scroll key to view the alarm.

This message will be displayed.

Restore the sensor to normal, close door/window or stop motion, and the LCD

display will return to the disarmed state.

5.Press the [F] key to initiate an alarm. The Bell will sound pulsing. Arm then

quickly disarm the panel to silence the signal and return to the disarmed state.

6.If the FIRE zone is enabled, activation will cause the signal to sound pulsing.

Caution: Do not use open flame or burning materials to test a smoke

detector. Contact your installer for information on safe methods to test

smoke detectors.

7.Should the system fail to function properly, call your alarm dealer for service.

8.When testing is complete, call and advise the monitoring station.

Note: Not all features described will be functional unless enabled by your

installer. Ensure your installer has advised you which features are functional

on your system.

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

DSC PC1500 - REV8 Instruction Manual Page 9

Comments to this Manuals

Related products and manuals for Fire protection DSC PC1500 - REV8