DSC PC5020 Installation Manual download pdf (Page 51)

WARNING Please Read Carefully

Note to Installers

This warning contains vital information. As the only individual in contact with system users, it is your

responsibility to bring each item in this warning to the attention of the users of this system.

System Failures

This system has been carefully designed to be as effective as possible. There are circumstances, however,

involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm sys-

tem of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons.

Some but not all of these reasons may be:

■ Inadequate Installation

A security system must be installed properly in order to provide adequate protection. Every installation

should be evaluated by a security professional to ensure that all access points and areas are covered. Locks

and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings

and other building materials must be of sufficient strength and construction to provide the level of protection

expected. A reevaluation must be done during and after any construction activity. An evaluation by the fire

and/or police department is highly recommended if this service is available.

■ Criminal Knowledge

This system contains security features which were known to be effective at the time of manufacture. It is

possible for persons with criminal intent to develop techniques which reduce the effectiveness of these fea-

tures. It is important that a security system be reviewed periodically to ensure that its features remain effec-

tive and that it be updated or replaced if it is found that it does not provide the protection expected.

■ Access by Intruders

Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by

moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent

the proper operation of the system.

■ Power Failure

Control units, intrusion detectors, smoke detectors and many other security devices require an adequate

power supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail.

Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a

device operates only by AC power, any interruption, however brief, will render that device inoperative while

it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations

which may damage electronic equipment such as a security system. After a power interruption has occurred,

immediately conduct a complete system test to ensure that the system operates as intended.

■ Failure of Replaceable Batteries

This system’s wireless transmitters have been designed to provide several years of battery life under normal

conditions. The expected battery life is a function of the device environment, usage and type. Ambient con-

ditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the

expected battery life. While each transmitting device has a low battery monitor which identifies when the

batteries need to be replaced, this monitor may fail to operate as expected. Regular testing and maintenance

will keep the system in good operating condition.

■ Compromise of Radio Frequency (Wireless) Devices

Signals may not reach the receiver under all circumstances which could include metal objects placed on or

near the radio path or deliberate jamming or other inadvertent radio signal interference.

■ System Users

A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary

physical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is

important that all system users be trained in the correct operation of the alarm system and that they know

how to respond when the system indicates an alarm.

■ Smoke Detectors

Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of rea-

sons, some of which follow. The smoke detectors may have been improperly installed or positioned. Smoke

may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the

other side of closed doors. Smoke detectors may not detect smoke from fires on another level of the resi-

dence or building.

Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot

sense all types of fires equally well. Smoke detectors may not provide timely warning of fires caused by

carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of

flammable materials, overloaded electrical circuits, children playing with matches or arson.

Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warn-

ing to allow all occupants to escape in time to avoid injury or death.

■ Motion Detectors

Motion detectors can only detect motion within the designated areas as shown in their respective installation

instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not

provide volumetric area protection. They have multiple beams of detection and motion can only be detected

in unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceil-

ings, floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether intentional

or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows or

any other part of the detection system will impair its proper operation.

Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness

can be reduced when the ambient temperature rises near or above body temperature or if there are intentional

or unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters,

radiators, stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on.

■ Warning Devices

Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if

there is an intervening wall or door. If warning devices are located on a different level of the residence or

premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may

be interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appli-

ances, or passing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired

person.

■ Telephone Lines

If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time.

Also an intruder may cut the telephone line or defeat its operation by more sophisticated means which may

be difficult to detect.

■ Insufficient Time

There may be circumstances when the system will operate as intended, yet the occupants will not be pro-

tected from the emergency due to their inability to respond to the warnings in a timely manner. If the system

is monitored, the response may not occur in time to protect the occupants or their belongings.

■ Component Failure

Although every effort has been made to make this system as reliable as possible, the system may fail to func-

tion as intended due to the failure of a component.

■ Inadequate Testing

Most problems that would prevent an alarm system from operating as intended can be found by regular test-

ing and maintenance. The complete system should be tested weekly and immediately after a break-in, an

attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or

outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating

devices and any other operational devices that are part of the system.

■ Security and Insurance

Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm sys-

tem also is not a substitute for property owners, renters, or other occupants to act prudently to prevent or

minimize the harmful effects of an emergency situation.

Limited Warranty

Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months from the

date of purchase, the product shall be free of defects in materials and workmanship under normal use. Dur-

ing the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective

product upon return of the product to its factory, at no charge for labour and materials. Any replacement and/

or repaired parts are warranted for the remainder of the original warranty or ninety (90) days, whichever is

longer. The original owner must promptly notify Digital Security Controls Ltd. in writing that there is defect

in material or workmanship, such written notice to be received in all events prior to expiration of the war-

ranty period.

International Warranty

The warranty for international customers is the same as for any customer within Canada and the United

States, with the exception that Digital Security Controls Ltd. shall not be responsible for any customs fees,

taxes, or VAT that may be due.

Warranty Procedure

To obtain service under this warranty, please return the item(s) in question to the point of purchase. All

authorized distributors and dealers have a warranty program. Anyone returning goods to Digital Security

Controls Ltd. must first obtain an authorization number. Digital Security Controls Ltd. will not accept any

shipment whatsoever for which prior authorization has not been obtained.

Conditions to Void Warranty

This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover:

• damage incurred in shipping or handling;

• damage caused by disaster such as fire, flood, wind, earthquake or lightning;

• damage due to causes beyond the control of Digital Security Controls Ltd. such as excessive voltage,

mechanical shock or water damage;

• damage caused by unauthorized attachment, alterations, modifications or foreign objects;

• damage caused by peripherals (unless such peripherals were supplied by Digital Security Controls Ltd.);

• defects caused by failure to provide a suitable installation environment for the products;

• damage caused by use of the products for purposes other than those for which it was designed;

• damage from improper maintenance;

• damage arising out of any other abuse, mishandling or improper application of the products.

Digital Security Controls Ltd.’s liability for failure to repair the product under this warranty after a reason-

able number of attempts will be limited to a replacement of the product, as the exclusive remedy for breach

of warranty. Under no circumstances shall Digital Security Controls Ltd. be liable for any special, incidental,

or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or

any other legal theory. Such damages include, but are not limited to, loss of profits, loss of the product or any

associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services,

down time, purchaser’s time, the claims of third parties, including customers, and injury to property.

Disclaimer of Warranties

This warranty contains the entire warranty and shall be in lieu of any and all other warranties,

whether expressed or implied (including all implied warranties of merchantability or fitness for a par-

ticular purpose) And of all other obligations or liabilities on the part of Digital Security Controls Ltd.

Digital Security Controls Ltd. neither assumes responsibility for nor authorizes any other person pur-

porting to act on its behalf to modify or to change this warranty, nor to assume for it any other war-

ranty or liability concerning this product.

This disclaimer of warranties and limited warranty are governed by the laws of the province of

Ontario, Canada.

WARNING: Digital Security Controls Ltd. recommends that the entire system be completely tested on a

regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electri-

cal disruption, it is possible for this product to fail to perform as expected.

Installer’s Lockout

Any products returned to DSC which have the Installer’s Lockout option enabled and exhibit no other prob-

lems will be subject to a service charge.

Out of Warranty Repairs

Digital Security Controls Ltd. will at its option repair or replace out-of-warranty products which are returned

to its factory according to the following conditions. Anyone returning goods to Digital Security Controls

Ltd. must first obtain an authorization number. Digital Security Controls Ltd. will not accept any shipment

whatsoever for which prior authorization has not been obtained.

Products which Digital Security Controls Ltd. determines to be repairable will be repaired and returned. A

set fee which Digital Security Controls Ltd. has predetermined and which may be revised from time to time,

will be charged for each unit repaired.

Products which Digital Security Controls Ltd. determines not to be repairable will be replaced by the nearest

equivalent product available at that time. The current market price of the replacement product will be

charged for each replacement unit.

WWW.DIYALARMFORUM.COM

1 2 ... 46 47 48 49 50 51 52 53

Comments to this Manuals

No comments

DSC PC5020 Installation Manual Page 51

Comments to this Manuals

Related products and manuals for Security access control systems DSC PC5020