DSC PC 5010 Technical Information download pdf (Page 16)

AVIS: L’étiquette de l’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme à certaines normes de protection,

d’exploitation et de sécurité des réseaux de télécommunications. Industrie Canada n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.

Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’entreprise locale de télécommunication. Le matériel

doit également être installé en suivant une méthode acceptée de raccordement. L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions

énoncées ci-dessus n’empêchent pas la dégradation du service dans certaines situations.

Les réparations de matériel homologué doivent être effectuées par un centre d’entretien canadien autorisé désigné par le fournisseur. La compagnie de

télécommunications peut demander à l’utilisateur de débrancher un appareil à la suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de

mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’énergie électrique, les lignes téléphoniques et les canalisations

d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.

AVERTISSEMENT: L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service d’inspection des installations électriques,

ou à un électricien, selon le cas.

L’indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter toute surcharge, le pourcentage de la charge totale qui peut être raccordée à un circuit

téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit bouclé peut être constituée de n’importe quelle combinaison de dispositifs, pourvu que la

somme des indices de charge de l’ensemble des dispositifs ne dépasse pas 100.

L’Indice de charge de ce produit est 2.

NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network

protective, operational and safety requirements. Industry Canada does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment

must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent

degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to

this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

User should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if

present, are connected together. This precaution may be particularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device,

to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers

of all the devices does not exceed 100.

The Load Number of this unit is 2.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re-orient the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available

from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is a label that contains, among other information, the FCC registration number

of this equipment.

NOTIFICATION TO TELEPHONE COMPANY The customer shall notify the telephone company of the particular line to which the connection will be made,

and provide the FCC registration number and the ringer equivalence of the protective circuit.

FCC Registration Number: F53CAN-32163-AL-E

Ringer Equivalence Number: 0.0B

USOC Jack: RJ31X

TELEPHONE CONNECTION REQUIREMENTS Except for the telephone company provided ringers, all connections to the telephone network shall be made

through standard plugs and telephone company provided jacks, or equivalent, in such a manner as to allow for easy, immediate disconnection of the terminal

equipment. Standard jacks shall be so arranged that, if the plug connected thereto is withdrawn, no interference to the operation of the equipment at the customer’s

premises which remains connected to the telephone network shall occur by reason of such withdrawal.

INCIDENCE OF HARM Should terminal equipment or protective circuitry cause harm to the telephone network, the telephone company shall, where practicable,

notify the customer that temporary disconnection of service may be required; however, where prior notice is not practicable, the telephone company may temporarily

discontinue service if such action is deemed reasonable in the circumstances. In the case of such temporary discontinuance, the telephone company shall promptly

notify the customer and will be given the opportunity to correct the situation.

ADDITIONAL TELEPHONE COMPANY INFORMATION The security control panel must be properly connected to the telephone line with a USOC RJ-

31X telephone jack.

The FCC prohibits customer-provided terminal equipment be connected to party lines or to be used in conjunction with coin telephone service. Interconnect rules

may vary from state to state.

CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES The telephone company may make changes in its communications facilities, equipment, operations

or procedures, where such actions are reasonably required and proper in its business. Should any such changes render the customer’s terminal equipment incompatible with the

telephone company facilities the customer shall be given adequate notice to the effect modifications to maintain uninterrupted service.

RINGER EQUIVALENCE NUMBER (REN) The REN is useful to determine the quantity of devices that you may connect to your telephone line and still have all of

those devices ring when your telephone number is called. In most, but not all areas, the sum of the RENs of all devices connected to one line should not exceed five (5.0).

To be certain of the number of devices that you may connect to your line, you may want to contact your local telephone company.

EQUIPMENT MAINTENANCE FACILITY If you experience trouble with this telephone equipment, please contact the facility indicated below for information

on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until

you are sure that the equipment is not malfunctioning.

Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094

WARNING Please Read Carefully

Note to Installers

This warning contains vital information. As the only individual in contact

with system users, it is your responsibility to bring each item in this warning

to the attention of the users of this system.

System Failures

This system has been carefully designed to be as effective as possible. There

are circumstances, however, involving fire, burglary, or other types of emer-

gencies where it may not provide protection. Any alarm system of any type

may be compromised deliberately or may fail to operate as expected for a

variety of reasons. Some but not all of these reasons may be:

■ ■

■ Inadequate Installation

A security system must be installed properly in order to provide adequate

protection. Every installation should be evaluated by a security professional

to ensure that all access points and areas are covered. Locks and latches on

windows and doors must be secure and operate as intended. Windows, doors,

walls, ceilings and other building materials must be of sufficient strength

and construction to provide the level of protection expected. A reevaluation

must be done during and after any construction activity. An evaluation by

the fire and/or police department is highly recommended if this service is

available.

■ ■

■ Criminal Knowledge

This system contains security features which were known to be effective at

the time of manufacture. It is possible for persons with criminal intent to

develop techniques which reduce the effectiveness of these features. It is

important that a security system be reviewed periodically to ensure that its

features remain effective and that it be updated or replaced if it is found that

it does not provide the protection expected.

■ ■

■ Access by Intruders

Intruders may enter through an unprotected access point, circumvent a

sensing device, evade detection by moving through an area of insuffi-

cient coverage, disconnect a warning device, or interfere with or pre-

vent the proper operation of the system.

■ ■

■ Power Failure

Control units, intrusion detectors, smoke detectors and many other security

devices require an adequate power supply for proper operation. If a device

operates from batteries, it is possible for the batteries to fail. Even if the

batteries have not failed, they must be charged, in good condition and in-

stalled correctly. If a device operates only by AC power, any interruption,

however brief, will render that device inoperative while it does not have power.

Power interruptions of any length are often accompanied by voltage fluctua-

tions which may damage electronic equipment such as a security system.

After a power interruption has occurred, immediately conduct a complete

system test to ensure that the system operates as intended.

■ ■

■ Failure of Replaceable Batteries

This system’s wireless transmitters have been designed to provide several

years of battery life under normal conditions. The expected battery life is a

function of the device environment, usage and type. Ambient conditions such

as high humidity, high or low temperatures, or large temperature fluctua-

tions may reduce the expected battery life. While each transmitting device

has a low battery monitor which identifies when the batteries need to be

replaced, this monitor may fail to operate as expected. Regular testing and

maintenance will keep the system in good operating condition.

■ ■

■ Compromise of Radio Frequency (Wireless)

Devices

Signals may not reach the receiver under all circumstances which could

include metal objects placed on or near the radio path or deliberate

jamming or other inadvertent radio signal interference.

■ ■

■ System Users

A user may not be able to operate a panic or emergency switch possibly due

to permanent or temporary physical disability, inability to reach the device

in time, or unfamiliarity with the correct operation. It is important that all

system users be trained in the correct operation of the alarm system and that

they know how to respond when the system indicates an alarm.

■ ■

■ Smoke Detectors

Smoke detectors that are a part of this system may not properly alert occupants

of a fire for a number of reasons, some of which follow. The smoke detectors

may have been improperly installed or positioned. Smoke may not be able to

reach the smoke detectors, such as when the fire is in a chimney, walls or roofs,

or on the other side of closed doors. Smoke detectors may not detect smoke

from fires on another level of the residence or building.

Every fire is different in the amount of smoke produced and the rate of

burning. Smoke detectors cannot sense all types of fires equally well. Smoke

detectors may not provide timely warning of fires caused by carelessness

or safety hazards such as smoking in bed, violent explosions, escaping gas,

improper storage of flammable materials, overloaded electrical circuits, chil-

dren playing with matches or arson.

Even if the smoke detector operates as intended, there may be circumstances

when there is insufficient warning to allow all occupants to escape in time to

avoid injury or death.

■ ■

■ Motion Detectors

Motion detectors can only detect motion within the designated areas as

shown in their respective installation instructions. They cannot discrimi-

nate between intruders and intended occupants. Motion detectors do not

provide volumetric area protection. They have multiple beams of detec-

tion and motion can only be detected in unobstructed areas covered by

these beams. They cannot detect motion which occurs behind walls, ceil-

ings, floor, closed doors, glass partitions, glass doors or windows. Any

type of tampering whether intentional or unintentional such as masking,

painting, or spraying of any material on the lenses, mirrors, windows or

any other part of the detection system will impair its proper operation.

Passive infrared motion detectors operate by sensing changes in tempera-

ture. However their effectiveness can be reduced when the ambient tem-

perature rises near or above body temperature or if there are intentional or

unintentional sources of heat in or near the detection area. Some of these

heat sources could be heaters, radiators, stoves, barbeques, fireplaces, sun-

light, steam vents, lighting and so on.

■ ■

■ Warning Devices

Warning devices such as sirens, bells, horns, or strobes may not warn

people or waken someone sleeping if there is an intervening wall or door.

If warning devices are located on a different level of the residence or

premise, then it is less likely that the occupants will be alerted or awak-

ened. Audible warning devices may be interfered with by other noise

sources such as stereos, radios, televisions, air conditioners or other ap-

pliances, or passing traffic. Audible warning devices, however loud, may

not be heard by a hearing-impaired person.

■ ■

■ Telephone Lines

If telephone lines are used to transmit alarms, they may be out of service or busy

for certain periods of time. Also an intruder may cut the telephone line or defeat

its operation by more sophisticated means which may be difficult to detect.

■ ■

■ Insufficient Time

There may be circumstances when the system will operate as intended, yet the

occupants will not be protected from the emergency due to their inability to

respond to the warnings in a timely manner. If the system is monitored, the

response may not occur in time to protect the occupants or their belongings.

■ ■

■ Component Failure

Although every effort has been made to make this system as reliable as possible,

the system may fail to function as intended due to the failure of a component.

■ ■

■ Inadequate Testing

Most problems that would prevent an alarm system from operating as in-

tended can be found by regular testing and maintenance. The complete sys-

tem should be tested weekly and immediately after a break-in, an attempted

break-in, a fire, a storm, an earthquake, an accident, or any kind of con-

struction activity inside or outside the premises. The testing should include

all sensing devices, keypads, consoles, alarm indicating devices and any

other operational devices that are part of the system.

■ ■

■ Security and Insurance

Regardless of its capabilities, an alarm system is not a substitute for prop-

erty or life insurance. An alarm system also is not a substitute for prop-

erty owners, renters, or other occupants to act prudently to prevent or mini-

mize the harmful effects of an emergency situation.

1 2 ... 11 12 13 14 15 16 17

Comments to this Manuals

No comments

DSC PC 5010 Technical Information Page 16

Comments to this Manuals

Related products and manuals for Security access control systems DSC PC 5010